Slide
Back to list of products

Fan coil unitsConcealed

FANCOIL UNIT WITHOUT CASING, FOR HEATING AND COOLING, 2 AND 4 PIPES, CAPACITY FROM 0,62 kW TO 13,26 kW. The CONCEALED fancoil is a unit which can be used for ductwork installations: it has very good performances also with medium/long ducts, thanks to its high pressure centrifugal fans; it is silent and can be equipped with a wide range of dedicated accessories. The CONCEALED fancoil is available for vertical installation on the wall (with bottom air intake) or on the floor (with frontal air intake) and horizontal on the ceiling (with back or bottom air intake). This fancoil is the ideal solution for the needs of small spaces and limited sizes that nowadays influences the choice of furniture in homes or offices. Available in 11 sizes, the CONCEALED model is equipped with an electric box containing the terminal board and auxiliary drain pan. The frame is made of galvanized steel and the inner sides are completely lined by an insulating self-extinguishing material. To complete this model Eurapo offers a wide range of accessories. The concealed fancoils are also available for District Cooling applications: the water coils are designed with a reduced number of circuits, suitable for functioning with high water temperature difference.

accessories
  • BA1
    Additional heating coil for 4 pipe system
    find out more
  • BA41
    1-row coil in addition to 4-row coils
    find out more
  • KREL
    Electric heater
    find out more
  • CP CONCEALED
    Set of feet for CONCEALED (CV)
    find out more
  • _3A2+DT
    Valves and shut-off valves
    find out more
  • PC
    Condensate pump
    find out more
  • PAE/V
    Vertical external air intake with manual damper
    find out more
  • PAE/VM
    Vertical external air intake with motorized damper
    find out more
  • PAE/H
    Horizontal external air intake with manual damper
    find out more
  • PAE/HM
    Horizontal external air intake with motorized damper
    find out more
  • PAE/HAF
    Horizontal external air intake with manual damper
    find out more
  • AFT
    Anti-frost thermostat
    find out more
  • PA
    Air suction plenum
    find out more
  • PAS
    Air suction plenum with spigots
    find out more
  • PA90
    90° Air suction plenum
    find out more
  • RCA
    Duct connection
    find out more
  • PM
    Air delivery plenum with collars
    find out more
  • PM90
    90° Air delivery plenum
    find out more
  • RCCAF
    90° telescopic air intake connection
    find out more
  • TM
    Minimum water temperature thermostat TM
    find out more
  • BA1

    1-row heating coil for 4 pipe system, in addition to 2 and 3 row coils. Not available for PH and PH/AF models.

    BA41

    1-row additional heating coil for 4 pipe system in combination with 4 rows cooling coil.
    Its thickness is 60 mm and it is only available for CONCEALED units (CH, CV, CH/AF, CV/AF).

    KREL

    Electric heater supplied with 2 safety thermostats, one with automatic resetting and the other one with manual resetting (in accordance with B.T. 2006/95/CE, E.M.C. 2004/108/CE Directives)

    CP CONCEALED

    Set of feet in galvanized steel for CONCEALED model (CV).

    _3A2+DT

    3 ways ON/OFF valves, for 2 and 4 pipe system, with shut-off valves.

    PC

    The condensate pump is necessary when the natural water discharge is not allowed.

    Functions:
    • forced evacuation of the condensed water

    PAE/V

    PAE/V is a vertical external air intake with supporting feet and manual damper. All the elements are made of painted steel, in the same colour as the casing.
    The manual air damper provides the unit with a mixture of return air and outside air. An air intake at the rear of the fan coil must be included to provide fresh outside air.

    PAE/VM

    PAE/VM is a vertical external air intake with supporting feet and motorized damper.
    All the elements are made of painted steel. The motorized air damper is regulated by a servomotor and provides the unit with a mixture of return air and outside air.
    The servomotor operating mode depends on the required working conditions.
    An air intake at the rear of the fan coil must be included to provide fresh outside air.

    PAE/H

    Air suction plenum made of galvanized steel sheet, provided with a rectangular collar for the connection to the external air intake.
    It is mounted on the air intake of the unit, between the external air intake and the filter, which remains accessible for maintenance.
    The manual damper can be operated by a lever located on the side of the unit.

    PAE/HM

    Air suction plenum made of galvanized steel sheet, provided with a rectangular collar for the connection to the external air intake.
    It is mounted on the air intake of the unit, between the external air intake and the filter, which remains accessible for maintenance.
    The damper can be operated by a servomotor: ON/OFF (code LM230), ON/OFF with spring return (code LF230) or modulating with a proper controller (code LM24).

    PAE/HAF

    Air suction plenum made of galvanized steel sheet, provided with a rectangular collar for the connection to the external air intake.
    It is mounted on the air intake of the unit, between the external air intake and the filter, which remains accessible for maintenance.
    The manual damper can be operated by a lever located on the side of the unit.

    AFT

    When combined with a motorized dumper (either PAE/VM or PAE/HM), the anti-frost thermostat closes the dumper if the air temperature is below the set point (i.e. 0 °C), avoiding any damage to the coil caused by the frozen water inside it.

    PA

    The air suction plenum is made of galvanized steel sheet, provided with a rectangular collar for the connection to the external air intake.
    It is mounted on the air intake of the unit, between the external air intake and the filter, which remains accessible for maintenance.

    PAS

    Air suction plenum made of galvanized steel sheet, provided with collars (spigots) for the connection to the external air intake.
    It is mounted on the air intake of the unit, between the external air intake and the filter, which remains accessible for maintenance.

    PA90

    The 90° air suction plenum is made of galvanized steel sheet, provided with a rectangular collar for the connection to the external air intake.
    It is mounted on the air intake of the unit, between the external air intake and the filter, which remains accessible for maintenance.

    RCA

    This duct connection is made of galvanized steel, provided with a rectangular collar for the connection to the suction air duct.
    It is mounted on the air intake of the unit, between the duct and the filter, which remains accessible for maintenance.

    PM

    Air delivery plenum in galvanized steel provided with circular or rectangular collars, completely insulated inside, for the connection to the air ducts.
    It must be mounted on the air delivery of the unit.

    PM90

    90° air delivery plenum in galvanized steel provided with circular or rectangular collars, completely insulated inside, for the connection to the air ducts.
    It must be mounted on the air delivery of the unit.

    RCCAF

    The 90° telescopic air intake connection is made of galvanized steel sheet, it is complete with G3 filter.
    It must be mounted on the air intake of the unit. This connection can be mounted only on the CH unit specially pre-arranged.

    TM

    Bi metallic thermostat with fixed set point, to be used in heating only. It is factory mounted or, upon request, supplied separately as a kit. During heating operation, it prevents the fan from starting if the coil temperature has not reached the set point temperature

Omnibus 360 controls
  • ORx10
    OPower card with Modbus for asynchronous motors
    find out more
  • ORBx10
    OPower card with Modbus for brushless motors
    find out more
  • ORC336/ORC346
    Round Analog console for wall installation.
    find out more
  • ORC636/ORC646
    Round Cabin console for wall installation.
    find out more
  • ORC236/ORC246
    Round Display console for wall installation
    find out more
  • ORC436/ORC446
    Round Touch console for wall installation.
    find out more
  • ORS736/ORS746
    Round Manager supervisor for small systems (up to 16 units) on wall installation.
    find out more
  • ORS810
    Round Master supervisor for intermediate systems (up to 100 units)
    find out more
  • ORS940
    Round Net, an embedded system complete with web server, which allows the management of plants up to 250 units
    find out more
  • OIR30
    Infrared remote control
    find out more
  • Oxx50
    Multitask additional card
    find out more
  • BA1

    1-row heating coil for 4 pipe system, in addition to 2 and 3 row coils. Not available for PH and PH/AF models.

    BA41

    1-row additional heating coil for 4 pipe system in combination with 4 rows cooling coil.
    Its thickness is 60 mm and it is only available for CONCEALED units (CH, CV, CH/AF, CV/AF).

    KREL

    Electric heater supplied with 2 safety thermostats, one with automatic resetting and the other one with manual resetting (in accordance with B.T. 2006/95/CE, E.M.C. 2004/108/CE Directives)

    CP CONCEALED

    Set of feet in galvanized steel for CONCEALED model (CV).

    _3A2+DT

    3 ways ON/OFF valves, for 2 and 4 pipe system, with shut-off valves.

    PC

    The condensate pump is necessary when the natural water discharge is not allowed.

    Functions:
    • forced evacuation of the condensed water

    PAE/V

    PAE/V is a vertical external air intake with supporting feet and manual damper. All the elements are made of painted steel, in the same colour as the casing.
    The manual air damper provides the unit with a mixture of return air and outside air. An air intake at the rear of the fan coil must be included to provide fresh outside air.

    PAE/VM

    PAE/VM is a vertical external air intake with supporting feet and motorized damper.
    All the elements are made of painted steel. The motorized air damper is regulated by a servomotor and provides the unit with a mixture of return air and outside air.
    The servomotor operating mode depends on the required working conditions.
    An air intake at the rear of the fan coil must be included to provide fresh outside air.

    PAE/H

    Air suction plenum made of galvanized steel sheet, provided with a rectangular collar for the connection to the external air intake.
    It is mounted on the air intake of the unit, between the external air intake and the filter, which remains accessible for maintenance.
    The manual damper can be operated by a lever located on the side of the unit.

    PAE/HM

    Air suction plenum made of galvanized steel sheet, provided with a rectangular collar for the connection to the external air intake.
    It is mounted on the air intake of the unit, between the external air intake and the filter, which remains accessible for maintenance.
    The damper can be operated by a servomotor: ON/OFF (code LM230), ON/OFF with spring return (code LF230) or modulating with a proper controller (code LM24).

    PAE/HAF

    Air suction plenum made of galvanized steel sheet, provided with a rectangular collar for the connection to the external air intake.
    It is mounted on the air intake of the unit, between the external air intake and the filter, which remains accessible for maintenance.
    The manual damper can be operated by a lever located on the side of the unit.

    AFT

    When combined with a motorized dumper (either PAE/VM or PAE/HM), the anti-frost thermostat closes the dumper if the air temperature is below the set point (i.e. 0 °C), avoiding any damage to the coil caused by the frozen water inside it.

    PA

    The air suction plenum is made of galvanized steel sheet, provided with a rectangular collar for the connection to the external air intake.
    It is mounted on the air intake of the unit, between the external air intake and the filter, which remains accessible for maintenance.

    PAS

    Air suction plenum made of galvanized steel sheet, provided with collars (spigots) for the connection to the external air intake.
    It is mounted on the air intake of the unit, between the external air intake and the filter, which remains accessible for maintenance.

    PA90

    The 90° air suction plenum is made of galvanized steel sheet, provided with a rectangular collar for the connection to the external air intake.
    It is mounted on the air intake of the unit, between the external air intake and the filter, which remains accessible for maintenance.

    RCA

    This duct connection is made of galvanized steel, provided with a rectangular collar for the connection to the suction air duct.
    It is mounted on the air intake of the unit, between the duct and the filter, which remains accessible for maintenance.

    PM

    Air delivery plenum in galvanized steel provided with circular or rectangular collars, completely insulated inside, for the connection to the air ducts.
    It must be mounted on the air delivery of the unit.

    PM90

    90° air delivery plenum in galvanized steel provided with circular or rectangular collars, completely insulated inside, for the connection to the air ducts.
    It must be mounted on the air delivery of the unit.

    RCCAF

    The 90° telescopic air intake connection is made of galvanized steel sheet, it is complete with G3 filter.
    It must be mounted on the air intake of the unit. This connection can be mounted only on the CH unit specially pre-arranged.

    TM

    Bi metallic thermostat with fixed set point, to be used in heating only. It is factory mounted or, upon request, supplied separately as a kit. During heating operation, it prevents the fan from starting if the coil temperature has not reached the set point temperature

    ORx10

    Electronic card mounted on the unit, it is designed to fully regulate (directly or via Modbus) the water terminal units. The card is able to control: MANAGEMENT OF OUTPUTS/INPUTS: • ON/OFF 230V VALVES: 2 outputs (230V) for controlling the hot water valve and the cold water valve. • MODULATING VALVES: 2 analog 0-10V Outputs for controlling the hot water valve and the cold water valve. • FAN: 3 outputs (230V) for 3-speed control (Min-Med-Max). • ELECTRIC HEATER: 230V command signal for electrical resistance control. • ROOM TEMPERATURE: Analog input for the connection of a room temperature sensor. • WATER TEMPERATURE: Analog input for the connection of a water temperature probe • DELIVERY AIR TEMPERATURE: Analog input for the connection of a supply air temperature probe • WINDOW CONTACT: Configurable digital input for managing the window opening contact • MULTIFUNCTION INPUT: Configurable input for the management of differential pressure switch, STAND-BY forcing, Season changeover, AC motor alarm, Forcing ventilation, Economy, External temperature sensor. • PUMP/DIFFERENTIAL PRESSURE SWITCH ALARM: Configurable input for managing the condensate pump alarm or differential pressure switch alarm. COMMUNICATION PORTS: • MODBUS LOCAL BUS: 485 communication port with Modbus protocol for the MASTER / SLAVE connection of the units. • MODBUS CONSOLE BUS: 485 communication port with Modbus protocol for connecting the LOCAL Console. • MODBUS BMS BUS: 485 communication port with Modbus protocol for the connection of the BMS supervisor. INTERCONNECTION OF ADDITIONAL MULTIFUNCTION CARD: • CONNECTION FOR MULTITASK CARD: The multitask expansion card makes available through relays the contacts for controlling the 24V ON/OFF valves, alarm contact, fan contact or card status.

    ORBx10

    Electronic card mounted on the unit, it is designed to fully regulate (directly or via Modbus) the water terminal units. The card is able to control: MANAGEMENT OF OUTPUTS/INPUTS: • ON/OFF 230V VALVES: 2 outputs (230V) for controlling the hot water valve and the cold water valve. • MODULATING VALVES: 2 analog 0-10V Outputs for controlling the hot water valve and the cold water valve. • BRUSHLESS FAN: 0/10V analog output for controlling the brushless motor and relative input for managing any alarms. • ELECTRIC HEATER: 230V command signal for electrical resistance control. • ROOM TEMPERATURE: Analog input for the connection of a room temperature sensor. • WATER TEMPERATURE: Analog input for the connection of a water temperature probe • DELIVERY AIR TEMPERATURE: Analog input for the connection of a supply air temperature probe • WINDOW CONTACT: Configurable digital input for managing the window opening contact • MULTIFUNCTION INPUT: Configurable input for the management of differential pressure switch, STAND-BY forcing, Season changeover, AC motor alarm, Forcing ventilation, Economy, External temperature sensor. • PUMP/DIFFERENTIAL PRESSURE SWITCH ALARM: Configurable input for managing the condensate pump alarm or differential pressure switch alarm. COMMUNICATION PORTS: • MODBUS LOCAL BUS: 485 communication port with Modbus protocol for the MASTER / SLAVE connection of the units. • MODBUS CONSOLE BUS: 485 communication port with Modbus protocol for connecting the LOCAL Console. • MODBUS BMS BUS: 485 communication port with Modbus protocol for the connection of the BMS supervisor. INTERCONNECTION OF ADDITIONAL MULTIFUNCTION CARD: • CONNECTION FOR MULTITASK CARD: The multitask expansion card makes available through relays the contacts for controlling the 24V ON/OFF valves, alarm contact, fan contact or card status.

    ORC336/ORC346

    Round Analog console for wall installation. Available in white (ORC336) or black (ORC346). Functions: - On / Off status setting - Room temperature setting - Selection of the fan speed - Manual Summer / Winter changeover Also available for wall built-in "503" module (white ORC335 or black ORC345).

    ORC636/ORC646

    Round Cabin console for wall installation. Functions: - On / Off status setting - Room temperature setting - Selection of the ventilation speed and manual Summer / Winter switching are managed by the central system Also available for wall built-in "503" module (white ORC635 or black ORC645).

    ORC236/ORC246

    Round Display console for wall installation Available in white (ORC236) or black (ORC246). Functions and features: - Off / Economy / Comfort status - room temperature setting - operating mode setting (cooling-heating-ventilation) - fan speed selection - alarms and warnings - backlit display Also available for wall built-in "503" module (white ORC235 or black ORC245).

    ORC436/ORC446

    Available in white (ORC436) or black (ORC446). Functions and features: - Off / Economy / Comfort status - room temperature setting - operating mode setting (cooling-heating-ventilation) - 4.3 inch screen and capacitive touch - weekly programming of all units connected to the same network. Also available for wall built-in "503" module (white ORC435 or black ORC445).

    ORS736/ORS746

    Round Manager supervisor for small systems (up to 16 units), on wall installation. Available in white (ORS736) or black (ORS746). Functions: - 4.3 inch screen and capacitive touch - Wi-Fi connectivity - connection to a cloud server - remote management via dedicated app - IOT friendly - weekly programming of all units connected to the same network. Also available for wall built-in "503" module (white ORS735 or black ORS736).

    ORS810

    Round Master supervisor for intermediate systems (up to 100 units) Functions: - 7-inch screen and capacitive touch, - Wi-Fi connectivity - connection to a cloud server - remote management via dedicated app - IOT friendly - weekly programming of all units connected to the same network - allows interaction between different devices of the HVAC system: (cooling and heating units, HVAC system pumps, modulating valves for radiant systems, thermal zone valves, hydronic terminal units

    ORS940

    Round Net, an embedded system complete with web server, which allows the management of plants up to 250 units. Functions: - Wi-Fi connectivity - connection to a cloud server - remote management via dedicated app - IOT friendly - weekly programming of all units connected to the same network - allows interaction between different devices of the HVAC system: (cooling and heating units, HVAC system pumps, modulating valves for radiant systems, thermal zone valves, hydronic terminal units

    OIR30

    The INFRARED CONTROLLER is provided with: - IR transmitter - LCD display for the visualisation of the main working parameters - buttons for setting the main working parameters (Status, Fan mode, Mode, Setpoint, Economy function)

    Oxx50

    The Multitask Omnibus 360 card contains 5 relay (powered by OPower card), for the connection of: - 2 electro thermic valves, 24V~ with the same activation mode of VH and VC valves. - An auxiliary fan for air changing and/or free cooling - Contact for the external signal for one or more Warning status of the OPower card (warning for Air Sensor, Check Sensor, Fault Motor) - Contact to manage the external air damper.

EST controls
  • EDCR
    Remote microprocessor for brushless motor
    find out more
  • EST
    Brushless motor with inverter for fancoils
    find out more
  • BA1

    1-row heating coil for 4 pipe system, in addition to 2 and 3 row coils. Not available for PH and PH/AF models.

    BA41

    1-row additional heating coil for 4 pipe system in combination with 4 rows cooling coil.
    Its thickness is 60 mm and it is only available for CONCEALED units (CH, CV, CH/AF, CV/AF).

    KREL

    Electric heater supplied with 2 safety thermostats, one with automatic resetting and the other one with manual resetting (in accordance with B.T. 2006/95/CE, E.M.C. 2004/108/CE Directives)

    CP CONCEALED

    Set of feet in galvanized steel for CONCEALED model (CV).

    _3A2+DT

    3 ways ON/OFF valves, for 2 and 4 pipe system, with shut-off valves.

    PC

    The condensate pump is necessary when the natural water discharge is not allowed.

    Functions:
    • forced evacuation of the condensed water

    PAE/V

    PAE/V is a vertical external air intake with supporting feet and manual damper. All the elements are made of painted steel, in the same colour as the casing.
    The manual air damper provides the unit with a mixture of return air and outside air. An air intake at the rear of the fan coil must be included to provide fresh outside air.

    PAE/VM

    PAE/VM is a vertical external air intake with supporting feet and motorized damper.
    All the elements are made of painted steel. The motorized air damper is regulated by a servomotor and provides the unit with a mixture of return air and outside air.
    The servomotor operating mode depends on the required working conditions.
    An air intake at the rear of the fan coil must be included to provide fresh outside air.

    PAE/H

    Air suction plenum made of galvanized steel sheet, provided with a rectangular collar for the connection to the external air intake.
    It is mounted on the air intake of the unit, between the external air intake and the filter, which remains accessible for maintenance.
    The manual damper can be operated by a lever located on the side of the unit.

    PAE/HM

    Air suction plenum made of galvanized steel sheet, provided with a rectangular collar for the connection to the external air intake.
    It is mounted on the air intake of the unit, between the external air intake and the filter, which remains accessible for maintenance.
    The damper can be operated by a servomotor: ON/OFF (code LM230), ON/OFF with spring return (code LF230) or modulating with a proper controller (code LM24).

    PAE/HAF

    Air suction plenum made of galvanized steel sheet, provided with a rectangular collar for the connection to the external air intake.
    It is mounted on the air intake of the unit, between the external air intake and the filter, which remains accessible for maintenance.
    The manual damper can be operated by a lever located on the side of the unit.

    AFT

    When combined with a motorized dumper (either PAE/VM or PAE/HM), the anti-frost thermostat closes the dumper if the air temperature is below the set point (i.e. 0 °C), avoiding any damage to the coil caused by the frozen water inside it.

    PA

    The air suction plenum is made of galvanized steel sheet, provided with a rectangular collar for the connection to the external air intake.
    It is mounted on the air intake of the unit, between the external air intake and the filter, which remains accessible for maintenance.

    PAS

    Air suction plenum made of galvanized steel sheet, provided with collars (spigots) for the connection to the external air intake.
    It is mounted on the air intake of the unit, between the external air intake and the filter, which remains accessible for maintenance.

    PA90

    The 90° air suction plenum is made of galvanized steel sheet, provided with a rectangular collar for the connection to the external air intake.
    It is mounted on the air intake of the unit, between the external air intake and the filter, which remains accessible for maintenance.

    RCA

    This duct connection is made of galvanized steel, provided with a rectangular collar for the connection to the suction air duct.
    It is mounted on the air intake of the unit, between the duct and the filter, which remains accessible for maintenance.

    PM

    Air delivery plenum in galvanized steel provided with circular or rectangular collars, completely insulated inside, for the connection to the air ducts.
    It must be mounted on the air delivery of the unit.

    PM90

    90° air delivery plenum in galvanized steel provided with circular or rectangular collars, completely insulated inside, for the connection to the air ducts.
    It must be mounted on the air delivery of the unit.

    RCCAF

    The 90° telescopic air intake connection is made of galvanized steel sheet, it is complete with G3 filter.
    It must be mounted on the air intake of the unit. This connection can be mounted only on the CH unit specially pre-arranged.

    TM

    Bi metallic thermostat with fixed set point, to be used in heating only. It is factory mounted or, upon request, supplied separately as a kit. During heating operation, it prevents the fan from starting if the coil temperature has not reached the set point temperature

    ORx10

    Electronic card mounted on the unit, it is designed to fully regulate (directly or via Modbus) the water terminal units. The card is able to control: MANAGEMENT OF OUTPUTS/INPUTS: • ON/OFF 230V VALVES: 2 outputs (230V) for controlling the hot water valve and the cold water valve. • MODULATING VALVES: 2 analog 0-10V Outputs for controlling the hot water valve and the cold water valve. • FAN: 3 outputs (230V) for 3-speed control (Min-Med-Max). • ELECTRIC HEATER: 230V command signal for electrical resistance control. • ROOM TEMPERATURE: Analog input for the connection of a room temperature sensor. • WATER TEMPERATURE: Analog input for the connection of a water temperature probe • DELIVERY AIR TEMPERATURE: Analog input for the connection of a supply air temperature probe • WINDOW CONTACT: Configurable digital input for managing the window opening contact • MULTIFUNCTION INPUT: Configurable input for the management of differential pressure switch, STAND-BY forcing, Season changeover, AC motor alarm, Forcing ventilation, Economy, External temperature sensor. • PUMP/DIFFERENTIAL PRESSURE SWITCH ALARM: Configurable input for managing the condensate pump alarm or differential pressure switch alarm. COMMUNICATION PORTS: • MODBUS LOCAL BUS: 485 communication port with Modbus protocol for the MASTER / SLAVE connection of the units. • MODBUS CONSOLE BUS: 485 communication port with Modbus protocol for connecting the LOCAL Console. • MODBUS BMS BUS: 485 communication port with Modbus protocol for the connection of the BMS supervisor. INTERCONNECTION OF ADDITIONAL MULTIFUNCTION CARD: • CONNECTION FOR MULTITASK CARD: The multitask expansion card makes available through relays the contacts for controlling the 24V ON/OFF valves, alarm contact, fan contact or card status.

    ORBx10

    Electronic card mounted on the unit, it is designed to fully regulate (directly or via Modbus) the water terminal units. The card is able to control: MANAGEMENT OF OUTPUTS/INPUTS: • ON/OFF 230V VALVES: 2 outputs (230V) for controlling the hot water valve and the cold water valve. • MODULATING VALVES: 2 analog 0-10V Outputs for controlling the hot water valve and the cold water valve. • BRUSHLESS FAN: 0/10V analog output for controlling the brushless motor and relative input for managing any alarms. • ELECTRIC HEATER: 230V command signal for electrical resistance control. • ROOM TEMPERATURE: Analog input for the connection of a room temperature sensor. • WATER TEMPERATURE: Analog input for the connection of a water temperature probe • DELIVERY AIR TEMPERATURE: Analog input for the connection of a supply air temperature probe • WINDOW CONTACT: Configurable digital input for managing the window opening contact • MULTIFUNCTION INPUT: Configurable input for the management of differential pressure switch, STAND-BY forcing, Season changeover, AC motor alarm, Forcing ventilation, Economy, External temperature sensor. • PUMP/DIFFERENTIAL PRESSURE SWITCH ALARM: Configurable input for managing the condensate pump alarm or differential pressure switch alarm. COMMUNICATION PORTS: • MODBUS LOCAL BUS: 485 communication port with Modbus protocol for the MASTER / SLAVE connection of the units. • MODBUS CONSOLE BUS: 485 communication port with Modbus protocol for connecting the LOCAL Console. • MODBUS BMS BUS: 485 communication port with Modbus protocol for the connection of the BMS supervisor. INTERCONNECTION OF ADDITIONAL MULTIFUNCTION CARD: • CONNECTION FOR MULTITASK CARD: The multitask expansion card makes available through relays the contacts for controlling the 24V ON/OFF valves, alarm contact, fan contact or card status.

    ORC336/ORC346

    Round Analog console for wall installation. Available in white (ORC336) or black (ORC346). Functions: - On / Off status setting - Room temperature setting - Selection of the fan speed - Manual Summer / Winter changeover Also available for wall built-in "503" module (white ORC335 or black ORC345).

    ORC636/ORC646

    Round Cabin console for wall installation. Functions: - On / Off status setting - Room temperature setting - Selection of the ventilation speed and manual Summer / Winter switching are managed by the central system Also available for wall built-in "503" module (white ORC635 or black ORC645).

    ORC236/ORC246

    Round Display console for wall installation Available in white (ORC236) or black (ORC246). Functions and features: - Off / Economy / Comfort status - room temperature setting - operating mode setting (cooling-heating-ventilation) - fan speed selection - alarms and warnings - backlit display Also available for wall built-in "503" module (white ORC235 or black ORC245).

    ORC436/ORC446

    Available in white (ORC436) or black (ORC446). Functions and features: - Off / Economy / Comfort status - room temperature setting - operating mode setting (cooling-heating-ventilation) - 4.3 inch screen and capacitive touch - weekly programming of all units connected to the same network. Also available for wall built-in "503" module (white ORC435 or black ORC445).

    ORS736/ORS746

    Round Manager supervisor for small systems (up to 16 units), on wall installation. Available in white (ORS736) or black (ORS746). Functions: - 4.3 inch screen and capacitive touch - Wi-Fi connectivity - connection to a cloud server - remote management via dedicated app - IOT friendly - weekly programming of all units connected to the same network. Also available for wall built-in "503" module (white ORS735 or black ORS736).

    ORS810

    Round Master supervisor for intermediate systems (up to 100 units) Functions: - 7-inch screen and capacitive touch, - Wi-Fi connectivity - connection to a cloud server - remote management via dedicated app - IOT friendly - weekly programming of all units connected to the same network - allows interaction between different devices of the HVAC system: (cooling and heating units, HVAC system pumps, modulating valves for radiant systems, thermal zone valves, hydronic terminal units

    ORS940

    Round Net, an embedded system complete with web server, which allows the management of plants up to 250 units. Functions: - Wi-Fi connectivity - connection to a cloud server - remote management via dedicated app - IOT friendly - weekly programming of all units connected to the same network - allows interaction between different devices of the HVAC system: (cooling and heating units, HVAC system pumps, modulating valves for radiant systems, thermal zone valves, hydronic terminal units

    OIR30

    The INFRARED CONTROLLER is provided with: - IR transmitter - LCD display for the visualisation of the main working parameters - buttons for setting the main working parameters (Status, Fan mode, Mode, Setpoint, Economy function)

    Oxx50

    The Multitask Omnibus 360 card contains 5 relay (powered by OPower card), for the connection of: - 2 electro thermic valves, 24V~ with the same activation mode of VH and VC valves. - An auxiliary fan for air changing and/or free cooling - Contact for the external signal for one or more Warning status of the OPower card (warning for Air Sensor, Check Sensor, Fault Motor) - Contact to manage the external air damper.

    EDCR

    Microprocessor control, for "on wall" installation, designed for water terminal units equipped with Brushless motors (EST Inverter Technology): SV, SV/AF, PV, PV/AF, SVR.
    It permits to control the type of ventilation (fan thermostated or fan continuously running) the fan speeds (0-10V or Auto), SUMMER/WINTER switch and room temperature thermostat.

    EST

    The brushless electric motor is composed by a rotor having permanent magnets, whose magnetic fields interact with the ones producedby the stator winding.
    The transfer of current isno longer by mechanical commutation (sliding contacts) but by an electronic commutation system: one electronic controller (inverter) powers the motor’s stator and generates rotating magnetic fields, that determine the rotor’s speed.

standard controls
  • AS
    Air sensor
    find out more
  • CBL10
    Electric box CBL10
    find out more
  • CBL20
    Master & Slave card
    find out more
  • CBL30
    Electric box CBL30
    find out more
  • CER00
    Microprocessor control with thermostat, 3 speeds, Auto S/W switch
    find out more
  • CER10/B
    Microprocessor control as CER00 for modulating valves
    find out more
  • CER20
    Microprocessor control with thermostat, Auto speeds, Auto S/W switch
    find out more
  • CER30/B
    Microprocessor control as CER20, for modulating valves
    find out more
  • CER31
    Microprocessor control as CER30/B, power supply 24V
    find out more
  • CMR00
    Room temperature thermostat, 3 speeds, S/W switch
    find out more
  • CSROO
    Remote control panel 3 speeds
    find out more
  • TAD10
    Room temperature thermostat, S/W switch
    find out more
  • WS
    Water sensor
    find out more
  • BA1

    1-row heating coil for 4 pipe system, in addition to 2 and 3 row coils. Not available for PH and PH/AF models.

    BA41

    1-row additional heating coil for 4 pipe system in combination with 4 rows cooling coil.
    Its thickness is 60 mm and it is only available for CONCEALED units (CH, CV, CH/AF, CV/AF).

    KREL

    Electric heater supplied with 2 safety thermostats, one with automatic resetting and the other one with manual resetting (in accordance with B.T. 2006/95/CE, E.M.C. 2004/108/CE Directives)

    CP CONCEALED

    Set of feet in galvanized steel for CONCEALED model (CV).

    _3A2+DT

    3 ways ON/OFF valves, for 2 and 4 pipe system, with shut-off valves.

    PC

    The condensate pump is necessary when the natural water discharge is not allowed.

    Functions:
    • forced evacuation of the condensed water

    PAE/V

    PAE/V is a vertical external air intake with supporting feet and manual damper. All the elements are made of painted steel, in the same colour as the casing.
    The manual air damper provides the unit with a mixture of return air and outside air. An air intake at the rear of the fan coil must be included to provide fresh outside air.

    PAE/VM

    PAE/VM is a vertical external air intake with supporting feet and motorized damper.
    All the elements are made of painted steel. The motorized air damper is regulated by a servomotor and provides the unit with a mixture of return air and outside air.
    The servomotor operating mode depends on the required working conditions.
    An air intake at the rear of the fan coil must be included to provide fresh outside air.

    PAE/H

    Air suction plenum made of galvanized steel sheet, provided with a rectangular collar for the connection to the external air intake.
    It is mounted on the air intake of the unit, between the external air intake and the filter, which remains accessible for maintenance.
    The manual damper can be operated by a lever located on the side of the unit.

    PAE/HM

    Air suction plenum made of galvanized steel sheet, provided with a rectangular collar for the connection to the external air intake.
    It is mounted on the air intake of the unit, between the external air intake and the filter, which remains accessible for maintenance.
    The damper can be operated by a servomotor: ON/OFF (code LM230), ON/OFF with spring return (code LF230) or modulating with a proper controller (code LM24).

    PAE/HAF

    Air suction plenum made of galvanized steel sheet, provided with a rectangular collar for the connection to the external air intake.
    It is mounted on the air intake of the unit, between the external air intake and the filter, which remains accessible for maintenance.
    The manual damper can be operated by a lever located on the side of the unit.

    AFT

    When combined with a motorized dumper (either PAE/VM or PAE/HM), the anti-frost thermostat closes the dumper if the air temperature is below the set point (i.e. 0 °C), avoiding any damage to the coil caused by the frozen water inside it.

    PA

    The air suction plenum is made of galvanized steel sheet, provided with a rectangular collar for the connection to the external air intake.
    It is mounted on the air intake of the unit, between the external air intake and the filter, which remains accessible for maintenance.

    PAS

    Air suction plenum made of galvanized steel sheet, provided with collars (spigots) for the connection to the external air intake.
    It is mounted on the air intake of the unit, between the external air intake and the filter, which remains accessible for maintenance.

    PA90

    The 90° air suction plenum is made of galvanized steel sheet, provided with a rectangular collar for the connection to the external air intake.
    It is mounted on the air intake of the unit, between the external air intake and the filter, which remains accessible for maintenance.

    RCA

    This duct connection is made of galvanized steel, provided with a rectangular collar for the connection to the suction air duct.
    It is mounted on the air intake of the unit, between the duct and the filter, which remains accessible for maintenance.

    PM

    Air delivery plenum in galvanized steel provided with circular or rectangular collars, completely insulated inside, for the connection to the air ducts.
    It must be mounted on the air delivery of the unit.

    PM90

    90° air delivery plenum in galvanized steel provided with circular or rectangular collars, completely insulated inside, for the connection to the air ducts.
    It must be mounted on the air delivery of the unit.

    RCCAF

    The 90° telescopic air intake connection is made of galvanized steel sheet, it is complete with G3 filter.
    It must be mounted on the air intake of the unit. This connection can be mounted only on the CH unit specially pre-arranged.

    TM

    Bi metallic thermostat with fixed set point, to be used in heating only. It is factory mounted or, upon request, supplied separately as a kit. During heating operation, it prevents the fan from starting if the coil temperature has not reached the set point temperature

    ORx10

    Electronic card mounted on the unit, it is designed to fully regulate (directly or via Modbus) the water terminal units. The card is able to control: MANAGEMENT OF OUTPUTS/INPUTS: • ON/OFF 230V VALVES: 2 outputs (230V) for controlling the hot water valve and the cold water valve. • MODULATING VALVES: 2 analog 0-10V Outputs for controlling the hot water valve and the cold water valve. • FAN: 3 outputs (230V) for 3-speed control (Min-Med-Max). • ELECTRIC HEATER: 230V command signal for electrical resistance control. • ROOM TEMPERATURE: Analog input for the connection of a room temperature sensor. • WATER TEMPERATURE: Analog input for the connection of a water temperature probe • DELIVERY AIR TEMPERATURE: Analog input for the connection of a supply air temperature probe • WINDOW CONTACT: Configurable digital input for managing the window opening contact • MULTIFUNCTION INPUT: Configurable input for the management of differential pressure switch, STAND-BY forcing, Season changeover, AC motor alarm, Forcing ventilation, Economy, External temperature sensor. • PUMP/DIFFERENTIAL PRESSURE SWITCH ALARM: Configurable input for managing the condensate pump alarm or differential pressure switch alarm. COMMUNICATION PORTS: • MODBUS LOCAL BUS: 485 communication port with Modbus protocol for the MASTER / SLAVE connection of the units. • MODBUS CONSOLE BUS: 485 communication port with Modbus protocol for connecting the LOCAL Console. • MODBUS BMS BUS: 485 communication port with Modbus protocol for the connection of the BMS supervisor. INTERCONNECTION OF ADDITIONAL MULTIFUNCTION CARD: • CONNECTION FOR MULTITASK CARD: The multitask expansion card makes available through relays the contacts for controlling the 24V ON/OFF valves, alarm contact, fan contact or card status.

    ORBx10

    Electronic card mounted on the unit, it is designed to fully regulate (directly or via Modbus) the water terminal units. The card is able to control: MANAGEMENT OF OUTPUTS/INPUTS: • ON/OFF 230V VALVES: 2 outputs (230V) for controlling the hot water valve and the cold water valve. • MODULATING VALVES: 2 analog 0-10V Outputs for controlling the hot water valve and the cold water valve. • BRUSHLESS FAN: 0/10V analog output for controlling the brushless motor and relative input for managing any alarms. • ELECTRIC HEATER: 230V command signal for electrical resistance control. • ROOM TEMPERATURE: Analog input for the connection of a room temperature sensor. • WATER TEMPERATURE: Analog input for the connection of a water temperature probe • DELIVERY AIR TEMPERATURE: Analog input for the connection of a supply air temperature probe • WINDOW CONTACT: Configurable digital input for managing the window opening contact • MULTIFUNCTION INPUT: Configurable input for the management of differential pressure switch, STAND-BY forcing, Season changeover, AC motor alarm, Forcing ventilation, Economy, External temperature sensor. • PUMP/DIFFERENTIAL PRESSURE SWITCH ALARM: Configurable input for managing the condensate pump alarm or differential pressure switch alarm. COMMUNICATION PORTS: • MODBUS LOCAL BUS: 485 communication port with Modbus protocol for the MASTER / SLAVE connection of the units. • MODBUS CONSOLE BUS: 485 communication port with Modbus protocol for connecting the LOCAL Console. • MODBUS BMS BUS: 485 communication port with Modbus protocol for the connection of the BMS supervisor. INTERCONNECTION OF ADDITIONAL MULTIFUNCTION CARD: • CONNECTION FOR MULTITASK CARD: The multitask expansion card makes available through relays the contacts for controlling the 24V ON/OFF valves, alarm contact, fan contact or card status.

    ORC336/ORC346

    Round Analog console for wall installation. Available in white (ORC336) or black (ORC346). Functions: - On / Off status setting - Room temperature setting - Selection of the fan speed - Manual Summer / Winter changeover Also available for wall built-in "503" module (white ORC335 or black ORC345).

    ORC636/ORC646

    Round Cabin console for wall installation. Functions: - On / Off status setting - Room temperature setting - Selection of the ventilation speed and manual Summer / Winter switching are managed by the central system Also available for wall built-in "503" module (white ORC635 or black ORC645).

    ORC236/ORC246

    Round Display console for wall installation Available in white (ORC236) or black (ORC246). Functions and features: - Off / Economy / Comfort status - room temperature setting - operating mode setting (cooling-heating-ventilation) - fan speed selection - alarms and warnings - backlit display Also available for wall built-in "503" module (white ORC235 or black ORC245).

    ORC436/ORC446

    Available in white (ORC436) or black (ORC446). Functions and features: - Off / Economy / Comfort status - room temperature setting - operating mode setting (cooling-heating-ventilation) - 4.3 inch screen and capacitive touch - weekly programming of all units connected to the same network. Also available for wall built-in "503" module (white ORC435 or black ORC445).

    ORS736/ORS746

    Round Manager supervisor for small systems (up to 16 units), on wall installation. Available in white (ORS736) or black (ORS746). Functions: - 4.3 inch screen and capacitive touch - Wi-Fi connectivity - connection to a cloud server - remote management via dedicated app - IOT friendly - weekly programming of all units connected to the same network. Also available for wall built-in "503" module (white ORS735 or black ORS736).

    ORS810

    Round Master supervisor for intermediate systems (up to 100 units) Functions: - 7-inch screen and capacitive touch, - Wi-Fi connectivity - connection to a cloud server - remote management via dedicated app - IOT friendly - weekly programming of all units connected to the same network - allows interaction between different devices of the HVAC system: (cooling and heating units, HVAC system pumps, modulating valves for radiant systems, thermal zone valves, hydronic terminal units

    ORS940

    Round Net, an embedded system complete with web server, which allows the management of plants up to 250 units. Functions: - Wi-Fi connectivity - connection to a cloud server - remote management via dedicated app - IOT friendly - weekly programming of all units connected to the same network - allows interaction between different devices of the HVAC system: (cooling and heating units, HVAC system pumps, modulating valves for radiant systems, thermal zone valves, hydronic terminal units

    OIR30

    The INFRARED CONTROLLER is provided with: - IR transmitter - LCD display for the visualisation of the main working parameters - buttons for setting the main working parameters (Status, Fan mode, Mode, Setpoint, Economy function)

    Oxx50

    The Multitask Omnibus 360 card contains 5 relay (powered by OPower card), for the connection of: - 2 electro thermic valves, 24V~ with the same activation mode of VH and VC valves. - An auxiliary fan for air changing and/or free cooling - Contact for the external signal for one or more Warning status of the OPower card (warning for Air Sensor, Check Sensor, Fault Motor) - Contact to manage the external air damper.

    EDCR

    Microprocessor control, for "on wall" installation, designed for water terminal units equipped with Brushless motors (EST Inverter Technology): SV, SV/AF, PV, PV/AF, SVR.
    It permits to control the type of ventilation (fan thermostated or fan continuously running) the fan speeds (0-10V or Auto), SUMMER/WINTER switch and room temperature thermostat.

    EST

    The brushless electric motor is composed by a rotor having permanent magnets, whose magnetic fields interact with the ones producedby the stator winding.
    The transfer of current isno longer by mechanical commutation (sliding contacts) but by an electronic commutation system: one electronic controller (inverter) powers the motor’s stator and generates rotating magnetic fields, that determine the rotor’s speed.

    AS

    1 m length NTC sensor (10K, 25 °C), to be installed on the air intake of the fancoil unit.

    CBL10

    Self-extinguishing plastic box (class V0), which contains a 12 pole terminal board and a voltage transformer (230/24 V~ 10VA), for the electrical connection of the modulating valves.
    It is supplied as standard when the regulators CER10, CER30/B and CER31 are requested.

    CBL20

    Self-extinguishing plastic box (class V0), which contains a 12 pole terminal board and a power relay card (230 V~): this card is requested either when an electric heater is mounted on the fancoil unit or to control the fan speeds in Master/Slave configuration. It can be combined with the following regulators: CMR00, CER00 and CER20

    CBL30

    Self-extinguishing plastic box (class V0), which contains a 12 pole terminal board, a voltage transformer (230/24 V~ 10 VA) for the electrical connection of the modulating valves and/or 24V~ controls, a power relay card (24 V~), which is requested to control the fan speeds in Master/Slave configuration.
    It can be combined with the following regulators: CER10, CER31, CER00 and CER20 (with power supply 24 V).

    CER00

    Remote microprocessor control suitable for the complete control of a unit (fancoil, cassette, blower), in particular: type of ventilation (thermostated or continuously running), fan speed selection, Summer/Winter switch and room temperature thermostat. The controller is provided with terminals for the connection of other options:
    economy function (set-point variation of 6 °C), external centralized Summer/Winter changeover, window contact, minimum water temperature thermostat (TM) and cooling «EVC» and/or heating «EVH» on/off valves.

    FEATURES
    • Selector for the ventilation(THERMOSTATED – OFF – CONTINUOUSLY RUNNING).
    • Fan speed selector (HIGH – MED – LOW). A fourth position, with no symbol on it, allows only to reset the filter alarm. In no other situation the selector must stay in this position.
    • Room temperature knob (8÷30 °C). The «Comfort zone» is duly highlighted (about 20÷25 °C).
    • Plastic pins for limiting the temperature range.
    • Antifrost function.
    • LED signal for the operating mode.
    • LED signal for incorrect operation.

    CER10/B

    Remote microprocessor control suitable for the complete control of a unit (fancoil, cassette or sucted unit), in particular: type of ventilation (thermostated or continuously running), fan speed selection, Summer/Winter switch and room temperature thermostat. The controller is provided with terminals for the connection of other options: economy function (set-point variation of 6 °C), external centralized Summer/Winter changeover, window contact, minimum water temperature thermostat (TM) and cooling«EVC» and/or heating «EVH» modulating valves. Selector for the ventilation (THERMOSTATED – OFF – CONTINUOUSLY RUNNING). • Fan speed selector (HIGH – MED – LOW). A fourth position, with no symbol on it, allows only to reset the filter alarm. In no other situation the selector must stay in this position. • Room temperature knob (8÷30 °C). The «Comfort zone» is duly highlighted (about 20÷25 °C). • Plastic pins for limiting the temperature range. • Antifrost function. • LED signal for the operating mode.

    CER20

    Remote microprocessor control suitable for the complete control of a unit (fancoil, cassette, blower), in particular: type of ventilation (thermostated or continuously running), fan speed selection, Summer/Winter switch and room temperature thermostat.
    The controller is provided with terminals for the connection of other options: economy function (set-point variationof 6 °C), external centralized Summer/Winter change over, window contact, minimum water temperature thermostat (TM) and cooling «EVC» and/or heating «EVH» on/off valves.

    FEATURES
    • Selector for the ventilation (THERMOSTATED - OFF - CONTINUOUSLY RUNNING)
    • Fan speed selector (AUTO – HIGH – MED – LOW).
    • Room temperature knob (8÷30 °C). The «Comfort zone» is duly highlighted (about 20÷25 °C).
    • Plastic pins for limiting the temperature range.
    • LED signal for the operating mode.
    • LED signal for incorrect operation.

    CER30/B

    Remote microprocessor control suitable for the complete control of a unit (fancoil, cassette, blower), in particular: type of ventilation (thermostated or continuously running), fan speed selection, Summer/Winter switch and room temperature thermostat.
    The controller is provided with terminals for the connection of other options: economy function (set-point variation of 6 °C), external centralized Summer/Winter changeover, window contact, minimum water temperature thermostat (TM) and cooling «EVC» and/or heating «EVH» on/off valves.
    Power supply 230V

    CER31

    Remote microprocessor control suitable for the complete control of a unit (fancoil, cassette, blower), in particular: type of ventilation (thermostated or continuously running), fan speed selection, Summer/Winter switch and room temperature thermostat.
    The controller is provided with terminals for the connection of other options: economy function (set-point variation of 6 °C), external centralized Summer/Winter changeover, window contact, minimum water temperature thermostat (TM) and cooling «EVC» and/or heating «EVH» on/off valves.
    Power supply 24V

    CMR00

    The remote thermostat is suitable for the selection of the main functions of a unit (fancoil, cassette, blower): type of ventilation, fan speed selection, Summer/Winter switch and room temperature control.
    The controller is provided with terminals for the connection of the minimum water temperature thermostat (TM) and of the cooling «EVC» and/or heating «EVH» on/off valves.

    FEATURES
    • Selector for the ventilation (THERMOSTATED – OFF – CONTINUOUSLY RUNNING)
    • Fan speed selector (HIGH - MED - LOW)
    • WINTER – 0 – SUMMER selector
    • Room temperature knob (7÷30 °C). The «Comfort zone» is duly highlighted (about 20÷25 °C).
    • Plastic pins for limiting the temperature range

    CSROO

    Remote controller, suitable only for the fan speed selection of a unit (fancoil, cassette, blower) installed in 2 pipe systems.
    The controller is provided with terminals for the connection of the minimum water temperature thermostat (TM) and of a remote thermostat (mod. TAD10).

    FEATURES
    Fan speed selector (HIGH – OFF – MED – LOW)

    TAD10

    Remote room temperature thermostat with manual SUMMER/WINTER switch.
    It is provided with terminals for the connection to a regulating valve (2 pipe system only).

    WS

    3m length NTC sensor (10K, 25°C), requested when a fancoil unit is controlled by a regulator with microprocessor, in a 2 pipe system, for both heating and cooling operations.

applications
Sports Centres
Civil - Residential
Industrial
River and Sea Ships
Hospitals - Clinics
Special Buildings

request


informations

Fill in the following form with your request.
We will get back to you as soon as possible.